The Bulkhead Tank: a cage of dark grey stone round a glass window on each side, with cyan lamps up its corners
Capacity
32,000 mB
Transfer
1,000 mB/t
Slots
Containers in and out, kit
Upgrades
Tier kits
ID
enthalpy:bulkhead_tank

What it does#

Got fluid with nowhere to put it? The Bulkhead Tank stores it. Think of it as the fluid twin of the Voltaic Cell, with one block, one tank and any one fluid.

A base tank holds 32,000 mB and moves up to 1,000 mB/t in, and the same out. Break it and it keeps its fluid, so you can carry a pond of oil in your pocket.

You can see the fluid through the glass on every side. Lava and other fluids that give off light glow through it in the dark, so a tank of lava looks rather fine at night.

Its two slots fill buckets or any other fluid container from the tank, or empty them into it.

Building it#

Bulkhead TankCrafting Table

Using it#

  1. Place the tank next to whatever makes the fluid, or run a Sluice Conduit to it. Out of the box, it pushes fluid out of its front and takes it in everywhere else.
  2. Or use a full bucket on the tank to pour it in, and an empty bucket to fill it back up.
  3. Put containers in the top slot to fill or empty them in bulk.

Each tank is on its own. Tanks side by side or stacked don't join into one bigger tank.

Have a click around the screen below. The tabs and coloured faces work like the real thing. This one's a base tank, part full of water, about to fill some buckets.

Bulkhead TankRunning
4
Inventory
Stored19.2k / 32k mBIn1,000 mB/tOut0 mB/t
TankContainers
Fill
TierBaseCapacity32k mBTransfer1k mB/t
Auto-outputRedstone
Always
Low
High
  • Holds one fluid
  • Its slots fill or empty buckets; Fill or Empty switches which
Side ConfigInputOutputBothNone
  1. 1
    The fluid in the tank. Hover it for the fluid's name and the exact amount.
  2. 2
    Running while fluid is moving in or out through the faces. Idle when nothing is. Disabled when redstone has switched it off.
  3. 3
    What's stored, and how much came in and went out a moment ago, in mB/t.
  4. 4
    Containers go in here. Hoppers and pipes can put them in from any side.
  5. 5
    Finished containers come out here. Hoppers and pipes take them from any side.
  6. 6
    The Fill or Empty switch. Fill pours from the tank into the containers. Empty pours the containers into the tank.
  7. 7
    The tank's tier, its capacity and its transfer limit.
  8. 8
    The kit slot. The tank takes a tier kit and no modules.
  9. 9
    The faces' auto-output switch and redstone control.
  10. 10
    Which faces take fluid and which push it. Click a face to change it, and right-click to go back.

Filling and emptying containers#

The two slots on the Main tab work on buckets and on any container from another mod that holds fluid.

  • Fill: each empty container is filled from the tank and moved to the bottom slot.
  • Empty: each full container is poured into the tank and the empty one moved to the bottom slot.

The tank works through one container at a time, as long as the bottom slot has room for the result. A container it can't fill or empty waits in the top slot until it can.

The slots don't count against the transfer limit, and neither does a bucket you use on the block. So even a tank with busy faces fills your buckets at full speed.

Automation#

The faces start out like this.

The Front is set to Output, so it pushes fluid. Every other face is set to Input, so it takes fluid. Auto-output is on, and Auto-input is off.

With Auto-output on, the tank pushes fluid from its output faces into the tank, machine or Sluice Conduit band beside each one.

The transfer limit counts all the faces together, each way. A base tank takes in at most 1,000 mB/t, however many pipes feed it.

Hoppers and pipes can move containers too. On any face, they only put them in the top slot and only take them from the bottom one.

A comparator beside the tank gives 1 to 15 depending on how full it is, and nothing when it's empty. Use it to stop a pump when the tank is nearly full.

Side configuration explains faces, modes and redstone control for every machine.

Upgrades#

A tier kit raises both capacity and transfer. Each tier quadruples the capacity and doubles the transfer. Transfer matches a Sluice Conduit's pull collar of the same tier.

TierKitCapacityTransfer, in and out
BaseNone32,000 mB1,000 mB/t
TemperedTempered Upgrade Kit128,000 mB2,000 mB/t
FortifiedFortified Upgrade Kit512,000 mB4,000 mB/t
LuminousLuminous Upgrade Kit2,048,000 mB8,000 mB/t
HarmonicHarmonic Upgrade Kit8,192,000 mB16,000 mB/t
AllthemodiumAllthemodium Upgrade Kit32,768,000 mB32,000 mB/t
VibraniumVibranium Upgrade Kit131,072,000 mB64,000 mB/t
UnobtainiumUnobtainium Upgrade Kit524,288,000 mB128,000 mB/t

The Allthemodium, Vibranium and Unobtainium kits only exist in packs that have the Allthemodium mod.

The tier's jewel shows in the front's bottom beam.

Good to know#

  • The tank's silent, so it has no Sounds switch. It has no Auto-input either.
  • It holds one fluid at a time. Once it's empty, it takes any fluid again.
  • The tank keeps its fluid when broken, and the item's tooltip shows what's inside.
  • Redstone control pauses the container slots and auto-output. Pipes can still fill and drain the tank through its faces, within the same limit.
For pack makers: the settings behind these numbers
SettingDefaultRangeWhat it does
bulkheadTank.tierCapacity32,000 / 128,000 / 512,000 / 2,048,000 / 8,192,000 / 32,768,000 / 131,072,000 / 524,288,000Bulkhead Tank capacity per tier, in mB: base, tempered, fortified, luminous, harmonic, allthemodium, vibranium, unobtainium
bulkheadTank.tierTransfer1,000 / 2,000 / 4,000 / 8,000 / 16,000 / 32,000 / 64,000 / 128,000Bulkhead Tank input and output limit per tier, in mB/t, across all its faces: base, tempered, fortified, luminous, harmonic, allthemodium, vibranium, unobtainium. Its container slots don't count against it

The container slots and buckets used on the block don't count against the transfer limit.